Search results

  1. Anthony Bulger

    O2 Sensor wiring pinout

    Can someone verify my understanding of the wiring on the O2 sensor plug. Pin 1 - O2 Heat - 12Volt + Pin 2 - Ground - 12Volt - Pin 3 - O2 Return (Upstream or Downstream) - ? Pin 4 - O2 Signal - ? My questions are on Pin 3 & 4. Generally, 1 of these is a 0-1 volt output from the sensor since...
  2. Anthony Bulger

    Intermittent Electrical Module issue

    Ok so I have a 2019 Laramie Crew Cab 4x4 5.7L non etorc. She generally sits in the driveway during the week as I travel extensively for work. So, I only drive her occasionally on the weekends. Here is what has happened so far....... 3 weeks back, Friday went out to dinner with the little...
  3. Anthony Bulger

    5.7 Performance Part Questions

    Well, my 2019 5th Gen DT has rolled past 85K, and I've developed the dreaded cracked exhaust manifold leaks. So, I've decided that it's time to go ahead and do some preventative maintenance and through caution into the wind and UPGRADE STUFF! Here are my questions? 1. Long Tube Headers, ARH...
  4. Anthony Bulger

    Rear Locker Wiring Question

    I recently added the rear axle with 3.92's off a rebel into my 2019 Laramie. I got a Wiring Pigtail from Mopar and the Dash transmission knob with the locker button on it. I went in with AlphaOBDII and activated the switch and I get the proper messages now when I use it. I crawled under my...
  5. Anthony Bulger

    Transmission shifter?

    Does someone know a part number or the last eight of the vin. I’m trying to purchase a new shifter controller with the Axle lock and hill descent buttons on it. If it’s has the stop/start button that’s fine too Attached is a picture of one which will work. However I don’t need the stop/start...
  6. Anthony Bulger

    Axle fluid change

    I want to drain and examine a pair of used axles I bought. Was curious if someone knows the amount of Gear Oil I need for both front and rear. What grade? I assume I need Friction Modifier for both.
  7. Anthony Bulger

    6" Lift Fabtech or Zone and Why?

    Trying to decide which lift to go with. I like the Fabtech because it comes with the rear control arms and the Dirt Logic's. If I do Zone I was going to order Bilstein Coil over kit for the front and 5165's for the rear. As well as add some rear control arms. Any other add on suggestions...
  8. Anthony Bulger

    Spare tire after 35's or bigger?

    So I crawled under the truck and looked the other day and without removing the heat shields, I don't think I could even get a 33" tire under there, and then would the exhaust heat actually damage the tire. One would assume it would since they added the shields for the factory donut tire. So...
  9. Anthony Bulger

    Parking Brake application

    When I stop and turn the knob to park my parking brake auto sets. I don't remember it doing this when I first got the truck. I also now have to disengage it (Parking brake) when I turn the knob to drive. Did I change a setting somewhere by accident? Thanks
  10. Anthony Bulger

    What kind of trimming is needed for 37's

    Was contemplating 37's on 2019 DT Laramie 4x4. Can it be down with a 4" lift like an AEV or Zone or do you really have to go the 6" route. Can the factory 22" wheel still be used, or does in need more backspacing added? Or would it just be best to drop down to a 20" wheel, I know the tires are...
  11. Anthony Bulger

    Re-Gearing for Lift

    I couldn't seem to find any info about this, hence the post. I have a 2019 Laramie 1500 4x4 crew cab. I want to lift but want to re-gear for the lift. As I understand there is nothing for the front diff as of now. However I understand you can replace it with an older diff from a 4th gen. my...

Latest posts

Staff online

Members online

... and 4 more.
Total: 1,283 (members: 54, guests: 1,229)
Robots: 1,921

Forum statistics

Threads
195,633
Posts
2,872,770
Members
156,463
Latest member
BobMc

Share this page

Top