What did you do with your 4th Gen this week?

[WY-Dave]

Driving a round without back seat and carpet is loud af :O


View attachment 542673

yup it is ahah

 

[LumberJakl]

Just picked up a 2016 6.7, my 2017 5.7 had its fun when I bought her brand new. Wanted a diesel for a long time and now I want 'new' problems that I am not aware of, haha.

 

[StateOfMind]

INSTANT +10HP

 

[Sean J Blackburn]

Cleaned the evaporator core and emptied my catch can.

 

[Sean J Blackburn]

Oh almost forgot! Finally chased down the annoying clunk in my rear end. I inspected everything in the rear suspension. Everything was fine, except my rear passenger lower shock bolt was extremely loose. It was so loose that the shock was rattling around. Not sure why that bolt backed off but torqued it down to spec and so far so good

 

[hunterdan]

Since my battery died the other day, I wanted to take the proper steps to try to prevent it from occuring again. I have a spare battery in the bed of my truck hooked to a winch, that charges off the trailer wiring. It was a straight shot, no relay or isolator. I bought a voltage sensitive relay that kicks on at 13.3V and off at 12.8V. Since the trailer harness is constantly powered, this should prevent the battery from sucking down current while the truck is off. Easy 3 wire connection and verified it worked.

 

[Racer9]

I did a little pinstriping.

 

[aszumilo]

INSTANT +10HP


View attachment 542740View attachment 542741View attachment 542742

I thought about doing something similar. Looks good. What kind of paint did you use?

 

[StateOfMind]

I thought about doing something similar. Looks good. What kind of paint did you use?

Duplicolor adhesion promoter, VHT paints and clear. very high temp paint isn't needed, as the engine cover doesn't get heat soaked like an engine block, but I had the black and clear, and wanted the paints to be same formulations, plus VHT makes a HEMI orange.

I shot a satin clear, but might go back with a flat clear, to knock some shine out of it, so it blends in with the rest of the bay

 

[ramsare4real]

OC
Miles on truck: 127526.
Miles on Oil: 9729.
Oil added: 1.5 qt.

Out/Off: Castrol Edge 5W-40 Euro + Fram Endurance
In/On: Castrol Edge 5W-40 Euro + Fram Ultra

Sample taken and on its way to Polaris. Will post results soon.

 

[Black-Wolf]

INSTANT +10HP


View attachment 542740View attachment 542741View attachment 542742

Damn! I tried to do something similar, but it didn't turn out as well as I thought it should... Cover's sitting in the garage awaiting the day when I decide to try again!

 

[ric221]

Installed some Wagner brake pads OEX-1084's on the front

 

[mullet6577]

Barely over 5k miles since last oil change but have a road trip coming up in a couple weeks so new RP 20-500 and PUP 5-w30 were done

 

[Kid's HEMI! !!]

at the moment i have it apart in the middle of doing wheel bearings just waiting on the delivery and i’ll put it back together

 

[nkfgh233]

Installed Bilstein 5100 rear shocks + TufTruck HD springs

 

[WY-Dave]

Just seen some )&(_(^*%*^%#*(*%'er hit my drivers taillight and a few scratches on the body.

 

[marine0311]

Finally was able to do some testing this week. Since I installed the tuner and downloaded Hemifever tune, nothing but rainy weather. Glad Sean was patient with me, as being computer savvy I am not.

 

[marine0311]

Finally was able to do some testing this week. Since I installed the tuner and downloaded Hemifever tune, nothing but rainy weather. Glad Sean was patient with me, as being computer savvy I am not.View attachment 543000View attachment 543001

 

[marine0311]

Still a little slow. I realize a 4 door 4x4 Laramie is no speed demon. However either fall or next spring I will add a cam, heads and exhaust. Don’t want to be slow when the twin turbo weed wackers want to red light race.

 

[BuschLatte420]

Had the lower and upper intermediate steering shafts replaced at the dealer @ 10,500 miles on my 2022 already, I’m pretty sure the classics are made from grade B parts! On the bright side that was for a rubbing noise under the dash, they said the coupler on the lower shaft was binding causing irregular wear on the bearing on the upper. What I thought was a alignment issue for the longest time was just the stupid shafts binding!!!