2015 6.4

[lpfm1990]

Want to waken up the sound, working on a budget thou. So a full system is not in the works.... Yet.... So in the mean time, I see the crazy huge muffed is just in place with clamps.... Now. Here's my question. Is it possible to just get some pipe from Napa (3.5 inch tubing i think it is???) and get it to connect even thou the outlet is offset on the muffler over where it comes in. Or am I forced to get a muffler of some sort from magnaflow or flow master and some pipe to connect it all?

 

[lpfm1990]

And might help to say my truck is a 3500 srw not the 2500 with the 5-link

Sent from my iPhone using Tapatalk

 

[1500ram12]

Depends on how much you want to spend right away. If you can find a muffler shop that could give you the correct bend for the offset you could be in it for under a $100. But you may get sick of the straight pipe sound. For around $200 you could pick up a MagnaFlow or Jones exhaust or Flowmaster with the right offset or enough offset and add some pipe.

Sent from my SM-N910V using Tapatalk

 

[lpfm1990]

What is the size of the pipe on these? 3.5"??? I think a muffler isn't crazy much. And just a section of pipe to connect. I'm leaving the resonator on for now.

In the summer/fall once I've worked enough overtime. There is a local guy who has the stuff and does pretty good work that will cut the y pipe. And run 2.5 or 3in pipe back with a set of mufflers (one for each side) and dump each side behind the rear tires out the side with stainless piping for $850 which I think is very reasonable


Sent from my iPhone using Tapatalk

 

[Am3gross]

i think i am going to go to the muffler shop tomorrow and try this out, just take off the muffler and put in some straight pipe.. shouldnt be more then 100 bucks but my shops around here are rip off artists.. we will see.. if you find out before me please let me know what you think, as i will do the same for you.

 

[lpfm1990]

I found on eBay that jegs has the flow master 40 series on sale for $82 (normal $121) so I clicked buy it now. And I just snagged a 4' section of aluminized pipe for $20, and some clamps. With shipping on the pipe. Permatex exhaust gasket goo. My grand total is $150. I have enough pipe left I could cut out the resonator if I wanted to...


Sent from my iPhone using Tapatalk

 

[lpfm1990]

I'm too lazy to go outside in the dark to see how the resonator is on the tail pipe. I have some options either cut and find a place to bend a pipe to fit. Or if I have to get a muffler clamp to clamp the pipe to the frame. Get a 45 or 90 and dump it infront of the axle. Or just go get a turn down and dump it under the bed... Wonder how that would sound.....


Sent from my iPhone using Tapatalk

 

[1500ram12]

Yes 3.5". Some videos on YouTube I watched people took 4" dpf back diesel exhaust and a 4-3.5" reducer adapter and went that route. Not any cheaper than the mufflex DOD250035.

Sent from my SM-N910V using Tapatalk

 

[lpfm1990]

Yes 3.5". Some videos on YouTube I watched people took 4" dpf back diesel exhaust and a 4-3.5" reducer adapter and went that route. Not any cheaper than the mufflex DOD250035.

Sent from my SM-N910V using Tapatalk

I would have done the mufflex but I can't find anything else if it would work on mine. It says only for 2500 with coil rear suspension. I'm a 3500 with leafs


Sent from my iPhone using Tapatalk

 

[1500ram12]

If you aren't going to order anything for a day or two, once it dries up enough so I can crawl under my truck I'll snap a few pics so you can compare. You can also shoot Matt at Moe's performance a email and see if he knows if it will fit.

Sent from my SM-N910V using Tapatalk

 

[lpfm1990]

I already bought a flow master delta force 40 and some pipe and butt connector clamps. So it should be all good to go. But. After watching YouTube. I'm half tempted to take the pipe to Cole muffler or somewhere and get that stuffed in place and just have the resonator for a "muffler"


Sent from my iPhone using Tapatalk

 

[Am3gross]

muffler shops are closed today... maybe tomorrow for me.

 

[Browny10783]

Has anyone done the muffler delete and left the resonator? Curious how it sounds

 

[lpfm1990]

It's in YouTube. Go on the mufflex website. And they have a link to a video with it straight piped


Sent from my iPhone using Tapatalk

 

[loveracing1988]

The problem you are going to run into is finding a shop that can bend 3.5" pipe. Also depending on where you live expect 1 to 2 years out of alumnized exhaust.

 

[lpfm1990]

The problem you are going to run into is finding a shop that can bend 3.5" pipe. Also depending on where you live expect 1 to 2 years out of alumnized exhaust.

I know. This is a short term "fix". I have plans for a stainless system. Cut after the cats. And run either 2.5 or 3" duals with side dumps behind the axle.


Sent from my iPhone using Tapatalk

 

[lpfm1990]

Pipe just showed up. No muffler. But taking ride to muffler shop to see if they can stuff it in place of muffler [emoji41][emoji41][emoji41][emoji41]


Sent from my iPhone using Tapatalk

 

[lpfm1990]

$45 to bend and install.... Should sound like a truck soon


Sent from my iPhone using Tapatalk

 

[lpfm1990]

Ohhhh this is the best money by far I've spent. I don't want to stop driving and flooring it


Sent from my iPhone using Tapatalk

 

[lpfm1990]

Here's some before and after. 0-60 at half throttle. And 0-100 full throttle. Video does it no justice. Sounds better if you use headphones. For info. I have 3.73 gears and about 400lbs of sand bags in the bed

http://youtu.be/VypwF7icfVE


Sent from my iPhone using Tapatalk