Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
I thought the 13&14 units couldn't support more than 1 camera, am I wrong about that?Just stumbled upon this ...
https://www.customtronix.com/products/jailbreaker-jigsaw-bundled/
Looks like Customtronix can once again enable ALL 3 video inputs on the 13-17 Harmon 8.4 radios using the Jailbreaker Jigsaw HW and Rax Jailbreaker SW !
@customtronix
All the 2013-17 Harmon 8.4 radios have the hardware/pinouts for 3 video inputs and aux/CdPlayer Audio inputs. See my notes here.I thought the 13&14 units couldn't support more than 1 camera, am I wrong about that?
Ok cool, thank you!!All the 2013-17 Harmon 8.4 radios have the hardware/pinouts for 3 video inputs and aux/CdPlayer Audio inputs. See my notes here.
Stellantis/Ram decided to allow only one input on the 13-15 Ram 8.4s when SW update 17.x came out. Which messed up some folks with BuCam and Cargo Cam on the 13-15 trucks/radios.
I had the Original Customtronix Jailbreaker working on a 14 Ra4 several years ago ... See here and video in action. I liked it a lot. You can also do the same thing with their Enzo/Enigma modules on the newer 4c radios. (I'd rather see a SW solution if the inputs are actually there vs have an extra camera interface module added switching video in on the 1 BuCam input ... But it just comes down to preference)
Yes this is a 4t gen classic with 5 lug truck. I called them but they were not willing to help with any info. I would like to enable the auto and duel temp control on my Uconnect.... And any word from the folks you bought the harness from? (I have dealt with them before, and I won't again)
Is this a 2019 4th gen classic 5 lug truck or newer 5th Gen with 6 lug
I hope you can help. I have a 2019 Ram 1500 classic Tradesman that came with the 5" blue tooth radio and I installed a RA4 #68270661AF with Nav. I also installed a harness from CarplayNav with control module P68105017AE
My original 7 speed fan now only goes up to 6 but some times goes up to 7 with no difference between 6 and 7 speed. Im also getting the 911 error even though I installed the 911 service disabler, Also my bezel is a dual zone with auto and I would like to enable the auto function.
Yes, I spoke to them but they were not much help. Yes its a 2019 4th Gen 5 lug
Yes this is a 4t gen classic with 5 lug truck. I called them but they were not willing to help with any info. I would like to enable the auto and duel temp control on my Uconnect.
good day all I am need of a little help. I have everything installed the radio 8.4 bezel harness and module.
The harness came from 4wheelElectronics ... it has a blue wire with black connector can not find where to install it and they are no help so far.
does anyone know where it goes or if I have correct harness. the problem I have now is the 7th speed does not work on blower motor but worked on original head unit AC controls and the AC does not go to full cold it blows warm air again it worked with original head unit AC controls.
With the 8.4 radio and original AC controls everything worked but when I put the module harness and bezel with controls I have that problem. I have measured data from head unit and all commands are seen I have no codes Witech sees no problem. yes I am a Tech with Chrysler. what am I missing?
thanks to all for any help
Sith
This is the way to go Mpgrimm2 knows what's up helped me out with what I needed and had me up and going in no time you are the man brother thanks
All I can say is M2MODS is the one stop shop for this. Wish I found him first and saved the headache for other stuff.